QUITE SIMPLY, THE BEST HEAD TO SHAFT CONNECTOR
YET INVENTED
Why it’s Better
- Lightest Head to Shaft Connector – only 4 grams!
- Full Shaft Insertion to Bottom of Bore
- No Shaft Tip Trim Necessary
- Epoxy-less Installation
- Only One Adapter Necessary for ALL Shafts & Heads of Same Diameter
- Complete 360° Shaft Orientation
- Proprietary Thread Design will NOT Strip or Seize
- No Special Tools Needed for Installation
- Economical Solution for Multiple Head & Shaft Fitting System
FROM THE DESK OF TOM WISHON:
“I’m very excited to be offering Spiralock® to clubmakers and fitters. Having developed a shaft to clubhead connector device approximately 12 years ago, I am keenly aware of the limitations and challenges that these systems must deal with. When I first evaluated Spiralock®, I immediately saw its potential to be the best shaft to clubhead connector system in the market to enable clubmakers to perfectly duplicate the performance of a normally assembled golf club for temporary clubfitting purposes.”
NOTES ON SPIRALOCK® USAGE
Use of Spiralock® requires heads to be prepared with proprietary Spiralock® threading. TWGT offers a wide selection of designs already threaded. See below right for available models and lofts. Any TWGT model or loft not listed can be threaded for $10/head. Allow two week turn around time.
Non-TWGT heads can be threaded upon request. Cost is $20/head. Allow two to three week turn around time.
For secure non-epoxy assembly, shaft tip diameter must be between 0.332” and 0.335” for woods and 0.367” and 0.370” for irons.
Tightening is done with commonly available wrenches: 0.335” Spiralock® uses a 12mm open end wrench; 0.370” Spiralock® uses a ½” open end wrench.
| How Does Spiralock® Compare? | ||
|---|---|---|
Spiralock |
Others |
|
Universal Application |
Yes |
Yes |
Full Insertion of Shaft |
Yes |
No |
No Epoxy Installation |
Yes |
No |
360° Shaft Orientation |
Yes |
No |
Single Connector - All Parts |
Yes |
No |
No Seize/Strip Threads |
Yes |
No |
No Tip Trimming for Drivers |
Yes |
No |
| Spiralock® Packages | |
|---|---|
SP-FITPKG-DR-A |
1 Driver, 3 Shafts, 1 Spiralock® |
SP-FITPKG-DR-B |
3 Drivers, 5 Shafts, 2 Spiralock®
|
SP-FITPKG-DR-C |
5 Drivers, 9 Shafts, 2 Spiralock®
|
SP-FITPKG-WD-D |
2 Fwys, 3 Shafts, 1 Spiralock®
|
SP-FITPKG-WD-E |
4 Fwys, 5 Shafts, 2 Spiralock®
|
SP-FITPKG-HY-F |
2 Hy, 2 Shafts, 1 Spiralock®
|
SP-FITPKG-IR-G |
2 Irons, 4 Shafts, 1 Spiralock® |
SP-FITPKG-IR-H |
4 Irons, 5 Shafts, 2 Spiralock® |
SP-FITPKG-IR-I |
5 Irons, 8 Shafts, 2 Spiralock® |
Above Are Suggested Packages that Reflect Significant Savings. |
|
| TWGT Spiralock® Models Available | |||
|---|---|---|---|
DRIVERS |
FWYS |
HYBRIDS |
IRONS (#6) |
919THI - 9° |
949MC - 16.5° |
331H - #3 |
979 |
919THI - 10.5° Draw Bias |
525GRT - 16.5° |
331H - #4 |
870 |
919THI - 11° |
919THI - 16.5° |
331H - #5 |
770 |
919THI - 13° |
730 HIGH |
730CL - #5 |
752 |
919THI - 15.5° |
915HL - #5 |
785HF - #4 |
730 |
730CL |
560 |
||
555C |
|||
555M |
|||